Gas bills climbing every winter
We measure steady-state efficiency and compare it to the furnace's rated AFUE. If it has dropped, we find the cause, whether that is a dirty flame sensor, restricted airflow, or a failing gas valve, and fix it.
Combustion analysis and airflow testing done right the first time
Furnace Efficiency Testing Ashland OH That Cuts Your Gas Bill
Furnace efficiency testing Ashland OH measures exactly how much of every gas dollar your system turns into heat. We run combustion analysis, static pressure checks, and temperature-rise readings on Carrier, Trane, Lennox, and Goodman equipment, then hand you a written report with the numbers. If your furnace is short cycling, blowing lukewarm air, or your January bill jumped again, this test tells you why. We serve Ashland County homes and businesses with same-day appointments.
Careful work. Honest options.
About this service
What Furnace Efficiency Testing Ashland OH Really Measures
Furnace efficiency testing Ashland OH is a diagnostic service that measures combustion efficiency, airflow, and heat delivery to find where your system wastes fuel. A technician drills a small test port in the flue, inserts a combustion analyzer, and reads oxygen, carbon dioxide, stack temperature, and carbon monoxide levels. At the same time, a manometer checks static pressure across the filter and evaporator coil while a multimeter verifies amp draw on the blower motor. You get a steady-state efficiency percentage, a temperature rise figure, and a clear list of what is costing you money.
Most Ashland homes we test were built between 1900 and 1985, and the ductwork has been added to, patched, and rerouted more than once. That history shows up as high static pressure, uneven room temperatures, and furnaces running longer than they should. A furnace performance testing Ashland visit in fall catches those problems before the first hard freeze. If you have been searching for furnace efficiency testing near me Ashland Ohio because your upstairs bedrooms never get warm, the answer is usually airflow, not the furnace itself.
- ✓ Lower Monthly Gas Bills
- ✓ Catch Heat Exchanger Cracks
- ✓ Stop Short Cycling
- ✓ Document Real Numbers
What's included
What Our Furnace Efficiency Testing Includes
Every efficiency test covers combustion, airflow, and electrical verification on your furnace. We also document everything in writing so you have a baseline for future comparisons. Add-ons like ductwork repair or part replacement are quoted separately if the test uncovers a problem that needs fixing.
✓
Combustion Analysis Report
Flue gas readings for oxygen, carbon dioxide, stack temperature, and carbon monoxide, taken at steady state with a calibrated combustion analyzer. You get the actual numbers, not a summary that says everything looks fine.
✓
Airflow And Static Pressure
Manometer readings before and after the filter, plus temperature rise between return and supply. This is where most Ashland efficiency problems hide, and the numbers tell you whether the ductwork or the furnace is the issue.
✓
Electrical Component Check
Amp draw on the blower and inducer motors, voltage at the control board and transformer, and capacitor condition. Weak components show up here before they fail and leave you without heat.
✓
Safety Verification
Carbon monoxide check in the flue and ambient air, venting inspection, and a heat exchanger look with an inspection camera. If anything is unsafe, we tell you immediately and explain your options.
✓
Written Recommendations
A clear summary of what we found, what it means, and what we recommend. You decide what to do next. No pressure, no upsell, just the information you need to make a decision.
How it works
How Our Efficiency Testing Process Works
01
Visual Inspection
We start with the furnace itself: filter condition, blower wheel, burners, wire harness, and the flue connection. A wire brush clears rust and debris from the burners so the combustion readings are honest. This step takes about 15 minutes and often turns up a furnace filter that has not been changed since last winter.
02
Combustion Analysis
A calibrated combustion analyzer goes into the flue test port. We record oxygen, carbon dioxide, stack temperature, and carbon monoxide while the furnace runs in steady state. Readings are logged at multiple points, not just one, because a furnace that has not been serviced in years will drift as it warms up.
03
Airflow Measurement
A manometer measures static pressure before and after the filter, and across the evaporator coil if you have central air. We also check temperature rise between the return and supply plenums. High static pressure is the most common efficiency killer in Ashland homes, and it is almost always a ductwork or filter problem, not a furnace problem.
04
Electrical Verification
A clamp meter and multimeter check amp draw on the blower motor and inducer motor, plus voltage at the control board and transformer. A thermocouple tester or flame sensor tester confirms ignition components are reading correctly. Weak capacitors and failing blower motors show up here long before they fail outright.
05
Report And Recommendations
You get a written summary with your efficiency percentage, temperature rise, CO reading, and static pressure numbers. We walk through what each figure means and what we recommend, from a simple filter change to ductwork repair. There is no pressure and no upsell. You decide what to do with the information.
Tools & methods
Tools And Methods We Use
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Combustion Analyzer
Reads oxygen, carbon dioxide, stack temperature, and carbon monoxide in the flue to calculate steady-state efficiency and flag safety issues.
Manometer
Measures static pressure across the filter, coil, and ductwork to find airflow restrictions that waste fuel and cause uneven heating.
Clamp Meter And Multimeter
Checks amp draw on the blower and inducer motors and verifies voltage at the control board, transformer, and wire harness connections.
Thermocouple Tester And Flame Sensor Tester
Confirms ignition components are reading correctly so we know whether a pilot or flame sensor problem is causing efficiency loss.
Inspection Camera
Lets us look inside the heat exchanger for cracks without disassembling the entire furnace, which matters on older Ashland units.
HVAC Gauges
Verifies inlet and manifold gas pressure so we know the gas valve is delivering the input the furnace was rated for.
Wire Brush
Cleans rust and debris from burners before combustion analysis so the readings reflect the furnace's true condition.
Real results
Before and after.
1920s Home In Historic Ashland
Before
A 1920s house with original ductwork and a standing pilot furnace. Gas bills had climbed 22 percent over two winters, and the upstairs never got above 64 degrees. Static pressure measured 0.9 inches of water column, well above the 0.5 target.
After
We cleaned the pilot assembly, replaced the thermocouple, sealed three disconnected duct runs, and corrected the filter size. Static pressure dropped to 0.52 inches, temperature rise came into the data plate range, and the upstairs reached 69 degrees. The next January bill was $58 lower.
Short Cycling In Ashland Heights
Before
A 2004 Goodman furnace short cycling every four minutes. The homeowner had replaced the igniter twice in two seasons. Combustion analysis showed erratic readings, and the manometer flagged a pressure switch that was not closing reliably.
After
We replaced the pressure switch and the weak blower capacitor, then re-tested. Cycle time went from four minutes to 14, combustion readings stabilized, and amp draw on the blower dropped from 8.2 to 6.4 amps. The homeowner has not replaced an igniter since.
Carbon Monoxide Found In South Ashland
Before
A homeowner booked a pre-winter test because the furnace smelled odd at startup. Combustion analysis read 180 ppm carbon monoxide in the flue, well above the 100 ppm threshold. An inspection camera confirmed a cracked heat exchanger.
After
We shut the furnace down, explained repair versus replacement, and the homeowner chose a new 96 percent AFUE unit. The replacement tested at 96.2 percent steady-state efficiency with CO at 22 ppm. The old furnace was removed and recycled.
Problems we solve
Problems Furnace Efficiency Testing Ashland OH Solves
Most efficiency complaints trace back to one of a handful of causes. Testing identifies which one is costing you money before you spend anything on parts.
Ask a pro →↗
Rooms that never reach the thermostat setting
Static pressure readings show whether the ductwork is the bottleneck. We repair leaks, replace undersized filters, and balance airflow so every room gets its share of heat.
Furnace short cycling on and off
Testing separates a pressure switch problem from a limit switch trip from an oversized furnace. We repair the actual cause instead of replacing parts until something works.
Carbon monoxide concerns
Combustion analysis reads CO in the flue, and we confirm heat exchanger condition with an inspection camera. If it is cracked, we walk you through repair versus replacement immediately.
Proof you can check
Licensed, Certified, And Local
✓
NATE CertificationNorth American Technician Excellence
✓
EPA Section 608 CertificationU.S. Environmental Protection Agency
✓
Ohio HVAC LicenseState of Ohio
✓
OSHA Safety ComplianceOccupational Safety and Health Administration
✓
NFPA 54 ComplianceNational Fire Protection Association
Customer reviews
What Ashland Homeowners Say
★★★★★
“Our 1920s house has never heated evenly, and we assumed it was just the age. The technician ran combustion analysis and found static pressure way too high from a filter we had been using wrong for years. He swapped it, cleaned the flame sensor, and re-tested. The upstairs bedrooms are finally warm, and our November bill was $41 lower than last year.”
DR
Dana R.Homeowner, Historic Ashland
✓ Verified“
★★★★★
“I called because the furnace was short cycling every few minutes. They tested it the same afternoon and found a stuck pressure switch plus a weak capacitor on the blower. Both were fixed on the spot. The report they left had actual numbers on it, which I appreciated. No pressure to buy anything I did not need.”
MT
Marcus T.Homeowner, Ashland Heights
✓ Verified★★★★★
“We booked the efficiency test before winter because our gas bills kept climbing. The combustion analyzer flagged elevated carbon monoxide, and they confirmed a cracked heat exchanger with a camera. They walked us through repair versus replacement honestly and did not push the expensive option. We replaced the furnace and the new one tested at 96 percent.”
KL
Karen L.Homeowner, South Ashland
✓ VerifiedMost furnace efficiency testing in Ashland OH runs $150 to $300 for a full combustion and airflow analysis, and that fee is often credited toward any repair we perform the same visit. Cost depends on system age, whether you have central air to check across the coil, and how many test points the ductwork requires. A basic single-stage furnace test sits at the low end; a zoned two-stage system with complex ductwork sits higher.
Three signs point to a furnace running below its rated efficiency: gas bills climbing without a rate increase, rooms that never reach the thermostat setting, and run times longer than 15 to 20 minutes per cycle. A furnace efficiency test in Downtown Ashland OH or anywhere in the county gives you a steady-state percentage so you know for certain. Anything under 80 percent on a modern furnace is worth investigating.
Yes, when the test finds a fixable problem. Dirty flame sensors, restricted filters, high static pressure, and short cycling all waste gas, and correcting them commonly recovers 5 to 15 percent of heating cost. On a $200 monthly winter bill, that is $10 to $30 back every month. The test itself pays for itself within one or two heating seasons in most Ashland homes.
A full test takes 60 to 90 minutes on a typical Ashland County furnace. Combustion analysis runs 20 to 30 minutes once the unit reaches steady state, airflow measurement takes another 15 to 20, and electrical checks add 10 to 15. Older furnaces that need burner cleaning first can push the visit to two hours. We schedule the window so you are not waiting around all afternoon.
More services
Related Services We Offer
Emergency Furnace RepairIf your efficiency test uncovers a failed gas valve or cracked heat exchanger, we handle the emergency repair. No heat in January is not something to wait on, and we treat it as the priority call it is.Explore →24/7 Furnace RepairEfficiency problems do not always wait for business hours. When a furnace quits at 2 a.m. in Ashland, our 24/7 line gets a technician moving. We diagnose first, then fix what is actually wrong.Explore →
Same-Day Furnace RepairMany efficiency issues we find during testing, like a dirty flame sensor or weak capacitor, can be repaired the same visit. That saves you a second appointment and gets your system running correctly right away.Explore →
Furnace Not Heating RepairA furnace that runs but does not heat is often an airflow or ignition problem that efficiency testing identifies. We trace the cause, whether it is a limit switch tripping or a gas valve not opening fully.Explore →
Furnace Blowing Cold Air RepairCold air from the vents usually means the blower is running without a flame, or the heat exchanger is not transferring heat. Testing separates those two causes quickly so the repair is targeted, not guesswork.Explore →
Furnace Ignition RepairIgnition problems show up in combustion readings as erratic or failed light-offs. We test the igniter, flame sensor, and control board, then repair or replace the failed component so the furnace lights reliably every cycle.Explore →
Furnace Pilot Light RepairStanding pilot furnaces in older Ashland homes often have pilot problems that hurt efficiency. We clean the orifice, check the thermocouple, and confirm the pilot holds before testing combustion.Explore →
Furnace Thermocouple ReplacementA weak thermocouple causes the pilot to drop out and the furnace to lock out. We test it with a thermocouple tester and replace it with the correct type for your furnace model.Explore → Ready when you are
Book Furnace Efficiency Testing Ashland OH Before Winter
Fall slots fill fast, and a furnace that tests poorly in October will cost you all winter. Call us at +14195820227 to schedule furnace efficiency testing Ashland OH at your home. Same-day appointments available, and the test fee is credited toward any repair we do the same visit.
Schedule My Test +14195820227 →
Request an appointment
Call Ashland Furnace Repair Pros
Call +14195820227 any time, day or night, and a live dispatcher will take your address and symptoms. We serve Ashland and Ashland County with same-day and emergency service. You can also email info@ashlandfurnacerepairpros.com and we will reply within one business hour.
Call anytime+14195820227Email the officeinfo@ashlandfurnacerepairpros.us
Office hoursOpen 24 hours · 7 days a week